| ||
Brother DCP130 Trouble Error Codes
|
Code
|
Description
|
26, 27, 28, 29
|
Cannot detect ink cartridges.
The ink has run out or the ink cartridge is not set into place. 26: Black ink 27: Yellow ink 28: Cyan ink 29: Magenta ink
Ink cartridge PCB defective
Main PCB defective
|
3X
|
Head/carriage unit travel error
- Any obstacles on the travel path of the head/carriage unit Carriage PCB broken Head/carriage unit broken CR encoder strip stained or scratched Carriage motor broken Main PCB defective Power supply PCB defective Maintenance unit defective
|
40
|
The casing internal temperature thermistor has detected abnormal temperature in the machine.
|
41
|
The head drive voltage has dropped from the high to low level in an abnormally short period.
Piezoelectric (PZT) ceramic actuator defective (Cracks or rare short)
|
42
|
The head drive voltage has not dropped from the high to low level within the specified period.
Piezoelectric (PZT) ceramic actuator defective
|
43
|
The head thermistor has been opened or shorted abnormally.
Head flat cables broken Head flat cables and carriage-head flat cable not connected correctly Carriage PCB defective Main PCB defective
|
44
|
The temperature of the print head driver has risen abnormally. The head driver chip temperature sensor in the COF detect abnormally high temperature.
Head property parameters incorrect in the EEPROM Head/carriage unit broken Head flat cables and carriage-head flat cable not connected correctly Head flat cables broken Carriage-head flat cable broken Main PCB defective
|
46
|
The number of performed purge sequences has reached the limit.
Purge counter overflown
The number of flushing count has reached the limit.
Flushing counter overflown
|
48
|
Weak connection of the head flat cables.
Head flat cables or carriage-head flat cable broken or not connected
|
49
|
The head drive voltage has not risen to the specified level.
Head flat cables and carriage-head flat cable not connected correctly Main PCB defective Power supply PCB defective
|
4F
|
The head drive voltage has dropped from the high to low level in an abnormally short period.
Piezoelectric (PZT) ceramic actuator defective (Cracks or rare short)
|
50, 51
|
The purge cam switch does not come ON or OFF even after the purge cam has been driven by the specified number of pulses.
Switching arm assembly not engaged correctly Ink cartridge/purge switch harness not connected correctly Purge cam switch broken Gear(s) on the maintenance unit broken Paper feed motor broken Main PCB defective.
|
52
|
The purge cam switch does not come ON at each detection point.
Switching arm assembly not engaged correctly Gear(s) on the maintenance unit broken Abnormal load applied to the purge cam Paper feed motor broken Main PCB defective
|
54, 55
|
The tube pump rotates abnormally.
Foreign materials in the machine Clutch gear broken PF encoder disk being in contact with the upper cover and deformed PF encoder PCB defective Main drain tube bent Purge cam gear broken Abnormal load applied to the purge cam Planetary arm assembly broken Main PCB defective Power supply PCB defective Paper feed motor defective PF roller gear L broken
|
57
|
After a purging operation, the head/carriage unit will not return to the home position (capping position).
Head cap unit, head wiper or other parts on the maintenance unit interfering with the head/carriage unit CR encoder strip stained Any obstacles on the travel path of the head/carriage unit Carriage motor defective Head/carriage unit defective Main PCB defective Power supply PCB defective
|
5A
|
The purge cam stops abnormally when it is in operation.
Purge cam gear broken Abnormal load applied to the purge cam PF encoder disk being in contact with the upper cover and deformed PF roller gear L broken Switching arm assembly broken Foreign materials in the machine Clutch gear broken PF sensor PCB defective Main PCB defective Power supply PCB defective Paper feed motor defective
|
5B
|
The pump stops abnormally during air ventilation.
Purge cam gear broken Abnormal load applied to the purge cam PF encoder disk being in contact with the upper cover and deformed PF roller gear L broken Switching arm assembly broken Foreign materials in the machine Clutch gear broken PF sensor PCB defective Main PCB defective Power supply PCB defective Paper feed motor defective
|
5C
|
The pump stops abnormally during purging operation.
Purge cam gear broken Abnormal load applied to the purge cam PF encoder disk being in contact with the upper cover and deformed PF roller gear L broken Switching arm assembly broken Foreign materials in the machine Clutch gear broken PF sensor PCB defective Main PCB defective Power supply PCB defective Paper feed motor defective
|
5D
|
Current protection for the driver IC activated when the purge cam was being driven.
|
| |||||||||||||||||||||||||||||||||||||||||
Code
|
Description
|
A2
|
Document length exceeding the scan limitation. During scanning, 90 cm or longer of a document is detected. During document feeding or ejecting, 400 cm or longer of a document is detected.
Document jam Document rear sensor actuator caught on the surrounding parts Document rear sensor broken
|
A3
|
The document rear sensor does not come ON during document pull-in operation.
Document jam Document rear sensor actuator caught on the surrounding parts Document rear sensor broken
|
A4
|
50% or more faulty of white level data. (Not used.)
|
A5
|
FAX scanning failure (1st time)
|
A6
|
FAX scanning failure (retry)
|
A7
|
Mismatch between the CIS type and ROM data
Scanner cover containing the improper CIS type installed at repair
|
A8
|
Color parameter matching error. (Used for monitoring bugs at the factory.)
|
AC
|
Less than 50% faulty of white level data. (Not used.)
|
AF
|
CIS positioning error
CIS flat cable broken or not connected CIS motor harness not connected properly CIS motor defective Drive unit defective CIS defective Main PCB defective
|
B1
|
Dark level offset data level error for scanning. (Not used.)
|
B2
|
Gain control data level error for scanning. (Not used.)
|
B3
|
Scan area left edge detection error. (Not used.)
|
B4
|
Scan area right edge detection error. (Not used.)
|
B5
|
Horizontal scanning edge reduction detection error in scanning area setting (Not used.)
|
B6
|
Horizontal scanning edge enlargement detection error in scanning area setting (Not used.)
|
B7
|
A/D converter reference voltage error (at High level). (Not used.)
|
B8
|
A/D converter reference voltage error (at Low level). (Not used.)
|
B9
|
Light emission intensity error of the LED array (Exceeding the upper limit).
CIS defective Main PCB defective
|
BB
|
White level data error.
CIS defective Main PCB defective
|
Code
|
Description
|
BD
|
Black level data error.
CIS defective Main PCB defective
|
BE
|
Scan starting edge detection error.
CIS defective CIS flat cable broken or not connected Main PCB defective White film stained in the scanner unit.
|
D0 ... DF
|
Modem error.
Main PCB defective
|
E2, E3
|
Wired LAN MAC address not registered.
MAC address not registered correctly
|
E4
|
Out of recording paper. (Not used.)
|
E6
|
Write error in EEPROM.
Main PCB defective
|
E8
|
Data scanning error during transmission.
CIS defective Main PCB defective
|
EA
|
Document removed at phase B
Document front sensor actuator caught on the surrounding parts Document front sensor defective Main PCB defective
|
EE
|
Playback IC error.
Main PCB defective
|
F3, F5
|
Internal software error.
Main PCB defective
|
F6
|
PC interface error.
Main PCB defective
|
F7
|
Memory card connection failure.
Memory card not inserted into the card slot properly
|
F8
|
Battery harness connection failure. (Only in the “Maintenance Mode”)
Battery harness not inserted correctly.
|
FF
|
Memory management error.
Main PCB defective
|
Download Service Manual,Error Codes,
Download Laptop,download drivers, download laptop Drivers,ALL LAPTOP DRIVER. DELL DRIVERS, HP DRIVERS, TOSHIBA DRIVERS, ACER DRIVERS , LENOVO DRIVERS , SONY DRIVERS, SUMSUNG DRIVERS, ASUS DRIVERS,Acer Drivers, Mutoh Drivers,Apple Drivers,OCE Drivers,Brother Drivers,OKI Drivers,Canon Drivers Olivetti Drivers,Duplo Drivers,Panasonic Drivers,Encad-Kodak Drivers,Printronix Drivers,Epson Drivers,Ricoh Drivers,HP Drivers,Riso Drivers,KIP Drivers,Konica Drivers,Samsung Drivers,Konica-Minolta Drivers,Sanyo Drivers,Kyocera-Mita Drivers,Sharp Drivers,Lexmark Drivers,Sony Drivers,LG Drivers,Star '
Brother Trouble Error Codes
DOWNLOAD SUMSUNG, LAPTOP DRIVERS.laptopdriver.com, download.com
Download Laptop,download drivers, download laptop Drivers,ALL LAPTOP DRIVER. DELL DRIVERS, HP DRIVERS, TOSHIBA DRIVERS, ACER DRIVERS , LENOVO DRIVERS , SONY DRIVERS, SUMSUNG DRIVERS, ASUS DRIVERS,Acer Drivers, Mutoh Drivers,Apple Drivers,OCE Drivers, Download HP Drivers,Brother Drivers,OKI Drivers,Canon Drivers Olivetti Drivers,Duplo Drivers,Download DELL laptop DRIVERS,Panasonic Drivers,Encad-Kodak Drivers,DELL LAPTOP DRIVERS, Printronix Drivers,Epson Drivers,Download ASUS DRIVERS, Ricoh Drivers,HP Drivers,Riso Drivers,KIP Drivers,Konica Drivers,DOWNLOAD SONY LAPTOP DRIVERS ,Samsung Drivers,Konica-Minolta Drivers,Download Canon Drivers ,Sanyo Drivers,Kyocera-Mita Drivers,Sharp Drivers,Lexmark Drivers,Sony Laptop Drivers,LG Drivers,Star ,Download Sony Laptop Drivers,
Download SONY LAPTOP DRIVERS,
DELL DRIVERS,
Download DELL DRIVERS
download laptop Drivers
Drivers,Mimaki Drivers,Toshiba Drivers,Minolta Drivers,Various Drivers,Muratec Drivers,Zebra Drivers,
DOWNLOAD ASUS LAPTOP DRIVERS,
DOWNLOAD SUMSUNG LAPTOP DRIVERS,
DOWNLOAD DELL LAPTOP DRIVERS,
Download Canon Copy Machine Drivers
Brother Trouble Error Codes,
Drivers for Windows XP & Vista,
Drivers for Windows 7 ,
Drivers for Windows 10,
Drivers for Windows Vista,
Drivers for Windows XP,
A Note S37SP Drivers for Windows XP & Vist,
Drivers,Mimaki Drivers,Toshiba Drivers,Minolta Drivers,Various Drivers,Muratec Drivers,Zebra Drivers
0 Comments