Canon Canofax L410 Error Codes List - Canon Canofax Download Driver - Canon i-SENSYS FAX-L410

 

Canon Canofax L410 Error Codes List - Canon Canofax Download Driver - Canon Canofax L410

Canon Canofax L230 Buy on amazon

Canon i-SENSYS FAX-L410

Download drivers, software, firmware and manuals and get access to troubleshooting resources for your FAX machine.

Download Driver Canon Canofax L230

Download Manuals Canon Canofax L230

Canon Canofax L410 Error Codes List

Code: E000-0000

Description:

Fixing Assembly does not start up within specified time.

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check that the heater resistance measured between 1PIN and 2PIN of the cable (J101) on the Main Controller Board is in the following range. Replace the Fixing Assembly when the resistance value is abnormal.

[1] 120 V machine - Heater resistance: 16.0 U ±7%

[2] 230 V machines - Heater resistance: 53.8 U ±7%

(2) Check the connection of connector (J101) on the Engine Controller Board.

(3) Check the connection of connector (J552) on Engine Controller Board.

(4) Replace the Fixing Assembly. (5) Replace the Engine Controller Board.

Code: E001-0000

Description:

Abnormally high temperature (detected by main thermistor)

Remedy:

The main thermistor detected an abnormally high temperature 235 deg C) during temperature control

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check that the heater resistance measured between 1PIN and 2PIN of the cable (J101) on the Main Controller Board is in the following range. Replace the Fixing Assembly when the resistance value is abnormal.

[1] 120 V machine - Heater resistance: 16.0 U ±7%

[2] 230 V machines - Heater resistance: 53.8 U ±7%

(2) Check the connection of connector (J101) on the Engine Controller Board.

(3) Check the connection of connector (J552) on Engine Controller Board.

(4) Replace the Fixing Assembly. (5) Replace the Engine Controller Board.

Code: E003-0000

Description:

Abnormal low-temperature detection

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check that the heater resistance measured between 1PIN and 2PIN of the cable (J101) on the Main Controller Board is in the following range. Replace the Fixing Assembly when the resistance value is abnormal.

[1] 120 V machine - Heater resistance: 16.0 U ±7%

[2] 230 V machines - Heater resistance: 53.8 U ±7%

(2) Check the connection of connector (J101) on the Engine Controller Board.

(3) Check the connection of connector (J552) on Engine Controller Board.

(4) Replace the Fixing Assembly.

(5) Replace the Engine Controller Board.

Code: E004-0000

Description:

Fixing power supply drive circuit error

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Replace the Engine Controller Board.

(2) Replace the Fixing Assembly.

Code: E100-0001

Description:

Error detection on any of scanner motor, laser unit, and BD detection at scanner area.

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Replace the Laser Scanner Unit.

(2) Replace the Engine Controller Board.

Code: E196-2000

Description:

ROM read/write error (Error in storing each setting values for user mode / service mode / factory mode)

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Update the set of the Controller Firmware

(2) Replace the Main Controller Board.

Code: E202-0002

Description:

Contact Sensor HP error, Failure in return

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor.

(2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor.

(3) Replace the Contact Sensor.

(4) Replace the Main Controller Board.

Code: E225-0001

Description:

Light intensity of a lamp is less or equal to the criteria

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor.

(2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor.

(3) Replace the Contact Sensor.

(4) Replace the Main Controller Board.

Code: E301-0001

Description:

Insufficient light intensity in shading

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check the connection of Flat Cable between Main Controller Board (J5) and Contact Sensor.

(2) Replace the Flat Cable between Main Controller Board (J5) and Contact Sensor.

(3) Replace the Contact Sensor.

(4) Replace the Main Controller Board.

Code: E736-0000

Description:

Communication error with CCU/modem, or no FAX board installed on FAX model

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check the connection of connectors between the Main Controller Board (J601, J602) and the FAXNCU Board (J1201, J1204).

(2) Replace the connectors between the Main Controller Board (J601, J602) and the FAX-NCU Board (J1201, J1204).

(3) Replace the FAX-NCU Board.

(4) Replace the Main Controller Board.

Code: E740-0002

Description:

Error detection on either Network Board or Mac address

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check the connection of the network cable.

(2) Replace the Main Controller Board.

Code: E744-0002

Description:

Language file error

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies. Update the set of the Controller Firmware.

Code: E744-4000

Description:

Engine ID error (Invalid engine connection is detected)

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Check the Engine Controller Board.

(2) Update the Engine Firmware.

(3) Update the set of the Controller Firmware

Code: E744-6000

Description:

Communication error with Wireless LAN board.

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Replace the Wireless LAN Board.

(2) Replace the Main Controller Board.

Code: E806-0000

Description:

Fan Motor cannot rotate at specified revolution speed

Remedy:

When the same error repeatedly occurs after several times of turning the power OFF/ON, execute the following remedies.

(1) Replace the Main Fan Unit.

(2) Replace the Engine Controller Board.